EMAIL SUPPORT

dclessons@dclessons.com

LOCATION

NZ

LAB Creating Admin VDC

LAB Creating Admin VDC

Posted on Jan 23, 2020 (0)

LAB Creating Admin VDC

Lab Task:

Create an Admin VDC in all three scenario given below:

  • Admin VDC at times of Initial Boot and fresh Installation
  • Admin VDC to change from default VDC to admin VDC
  • Create Admin VDC in such a way that it replaces the Default VDC and also create the New VDC and copy all non-global configuration in to new VDC.

Solution:

This is to shows the prompts at a clean bootup to enable the admin VDC:

Enter the password for "admin":
Confirm the password for "admin":
Do you want to enable admin vdc (yes/no) [n]: yes

This example shows the show vdc output before the admin VDC is created:

switch(config)# sh vdc
vdc_id       vdc_name        state         mac                           type                       lc
------          --------               -----           ----------                      ---------                  ------
1                 switch           active           00:26:98:0d:02:22    Ethernet        m1 f1 m1xl m2xl
2                 vdc2             active           00:26:98:0d:02:12    Ethernet        m1 f1 m1xl m2xl
3                 vdc3             active           00:26:98:0d:03:42    Ethernet        f2
!

Scenario 2:

switch(config)# system admin-vdc
!
All non-global configuration from the default vdc will be removed,
Are you sure you want to continue? (yes/no) [no] yes
!

This example shows the show vdc output after executing the system admin-vdc command:

switch(config)# sh vdc
vdc_id        vdc_name         state        mac                      type                        lc
------             --------              -----     ----------                     ---------                    ------
1                 switch             active     00:26:98:0d:02:22     Ethernet      m1 f1 m1xl m2xl
2                 vdc2               active     00:26:98:0d:02:12     Ethernet      m1 f1 m1xl m2xl
3                 vdc3               active     00:26:98:0d:03:42     Ethernet       f2

Scenario 3:

switch(config)# system admin-vdc migrate dclessons
!
All non-global configuration from the default vdc will be removed, Are you sure you want to continue? (yes/no) [no] yes
Note: Interface mgmt0 will not have its ip address migrated to the new vdc
Note: During migration some configuration may not be migrated.
Example: VTP will need to be reconfigured in the new vdc if it was enabled. Please refer to configuration guide for details. Please wait, this may take a while
Note: Ctrl-C has been temporarily disabled for the duration of this command
2012 Jul 5 22:20:58 switch %$ VDC-1 %$ %VDC_MGR-2-VDC_ONLINE: vdc 4 has come online
switch(config)#

shows the show vdc output after the admin VDC is created:

switch(config)# sh vdc
vdc_id        vdc_name           state             mac                           type                          lc
------              --------                 -----           ----------                     ---------                        ------
1                 switch                active          00:26:98:0d:02:22      Admin                        None
2                 vdc2                  active          00:26:98:0d:02:12      Ethernet                m1 f1 m1xl m2xl
3                 vdc3                  active          00:26:98:0d:03:42      Ethernet                        f2
4               dclessons           active          00:26:98:0d:03:32       Ethernet                m1 f1 m1xl m2xl


Comment

    You are will be the first.

LEAVE A COMMENT

Please login here to comment.